3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [creality]

51 questions
4
votes
2 answers

How to tell if I have TMC2208 or A4988 Drivers on Creality Silent V4.2.3 Board?

I have a new Creality Ender 2 Pro with a Creality 4.2.3 mainboard. I'm attempting to compile Marlin to fix a bug. How can I tell what driver chips I have on this board? I've narrowed it down to likely A4988 or TMC2208_STANDALONE or possibly the…
spuder
  • 221
  • 1
  • 3
  • 10
4
votes
2 answers

Ender 3 Pro will not auto home correctly after mainboard & BLTouch upgrades

I made two updates to my Ender 3 Pro: Silent Mainboard and BLTouch. My printer head is way out of sync now. After I Auto Home, it moves along the X-axis to the left, hits the stop switch & moves back to the right. It does not move at all on the…
wallwalker
  • 227
  • 1
  • 3
  • 10
4
votes
0 answers

Difference between Creality V2.1/V2.2 boards? Where to find datasheets?

I can't find an official datasheet for either board. Does anyone know where to find this information? Something that has max voltages, pinouts, etc. Also, what's the difference between the V2.1 and the V2.2?
cds333
  • 693
  • 3
  • 9
  • 17
3
votes
1 answer

Do you need the front fan on Ender 3 Pro?

I have a heating problem on my Ender 3 Pro. I changed the thermistor and the 40 W heater but still the printer will just heat to 200 °C. So I unplugged the front fan that runs constantly, and, yes, now it reaches 260 °C. Can I run my printer like…
Felix Wackenhuth
  • 31
  • 1
3
votes
2 answers

In Creality slicer, which settings should be adjusted to reduce the contact area between a support and an overhang?

In Creality slicer, which settings would you change to reduce the amount of surface area from the supporting structure that makes contact with overhangs on the model you are printing. For example, if you are printing the object pictured below, and…
Aaargh Zombies
  • 1,836
  • 1
  • 9
  • 27
3
votes
1 answer

Creality Ender 6 Heating Failed

There is a message on my Ender 6 that is telling my that my heating failed. This happened last night in the middle of a print. I have cycled the power like the screen says but the nozzle does not heat up. The print bed heats up just fine. The nozzle…
Quakenbush
  • 31
  • 2
3
votes
1 answer

Is it possible to run 2 Ender 3's off one power supply?

I have 2 Ender 3's and I am limited to wall sockets to power both the printers at the same time. So I was wondering if it was possible to wire both the printers to a single PSU? As the printer uses a single xt60 connecter for power to the mainboard,…
MeddlingSpy
  • 31
  • 1
3
votes
1 answer

Is Creality Ender 3 V2 Supposed To Come With Board V 4.2.2?

I recently purchased a Creality Ender 3 V2 ~1 month ago, and just yesterday installed a BLTouch. When looking at the motherboard, I noticed my board version is 4.2.2. Isn't the Ender 3 V2 supposed to come with a V 4.2.7 board? Did Creality…
Void_Frost
  • 43
  • 1
  • 8
2
votes
0 answers

I want to change default start position to the center of Creality CR 10 Smart Pro

Currently my 3D printer starts all projects from the lower left corner of the heatbed. I want to change the default setting to make the center of the heatbed the default position. However, I have not found any documentation on how to do this. Can…
Phil
  • 51
  • 1
2
votes
1 answer

What is the shaded area that appears around the outside of objects in Creality Slicer?

I'm using Creality Slicer, brims and other anti-warming or adhesion settings are all turned off. when I place an object on the bed a shaded area appears around it (See picture). Is this simply the area in which you can't print anything else in…
Aaargh Zombies
  • 1,836
  • 1
  • 9
  • 27
2
votes
1 answer

HALOT BOX makes objects with support move up

I'm trying to slice some models using the default HALOT BOX software from Creality, which comes with the Halot One resin 3D printer. I've oriented them at 45 degrees, and am using supports. When I come to slice the models, the models all jump up a…
user-596a6526
  • 103
  • 2
  • 10
2
votes
1 answer

Mid-print issue, extruder issue?

I have succumbed to asking the community for assistance. I've been scratching my head and lost many late nights and time trying to figure out what is going on with my 3D printer. Please see the image of what's going on with it. Sometimes my printer…
Dayclone
  • 21
  • 1
1
vote
0 answers

What causes these print issues after changes on my Creality CP-01 extruder?

I have a Creality CP-01 that has one of the feeders loose so I had to take down the entire extruder to fix it. After fixing it making sure it feeds properly and leveling the bed, it is producing what seems to be overflowing prints and I have no idea…
Marchal
  • 111
  • 3
1
vote
1 answer

Ender 3 S1 Pro error "extrude below min temp"

When I start my print it goes to home the z-axis and then I get the error "extrude below min temp" error (I have an Ender 3 S1 Pro)
Mr. Magic
  • 11
  • 1
1
vote
2 answers

How to fix a Creality Sonic Pad error that appears after the first few lines of printing?

I recently updated my Creality Sonic Pad to v1.0.6.49.145 (June 28, 2023 release) and since I applied that update, I've been consistently receiving the error when attempting to print any G-code file: Error Message: Unable to parse move 'G1 X251.931…
user37619
1
2 3 4