3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [skr-mini-e3]

25 questions
5
votes
2 answers

What can I do to remove the rounded corners using Junction Deviation?

I recently upgraded my Creality Ender 5 with an SKR Mini E3 V2.0 running Marlin 2.0.7.2. The printer has also been modified with an all-metal hotend and a direct drive conversion kit that uses the extruder stepper motor. In test prints of the XYZ…
user3883001
  • 51
  • 1
  • 1
  • 3
4
votes
0 answers

BLTouch not probing all points and motors making really loud noises since rebuild of latest Marlin (new hot end installed and BLTouch)

Please listen to this video, which illustrates the issue, with the sound on. Link to configuration.h and configuration_adv.h Machine Ender 3 Pro, New E3Dv6 hotend on a BMG Wind (all has been working and printing PLA, PETG, and TPU fine until I…
John Spencer
  • 149
  • 1
3
votes
1 answer

BTT SKR Mini E3 V3 w/BTT smart filament sensor

I'm trying to figure out how to get my BTT Smart Filament sensor to work with my printer. I have looked at Getting BTT filament sensor to work and have tried almost everything they did. Relevant Specs about my printer: Ender 3 (not pro or…
Semperfi89
  • 61
  • 5
3
votes
0 answers

Connecting 128x64 OLED to BIGTREETECH SKR mini E3

I'm trying to connect a 128x64 OLED display with the SH1106 driver for the BIGTREETECH SKR mini E3 printer controller board which uses the 32 bit STM32f103RC MCU. Note that it works fine with my RAMPS 1.4 board but when I compile it on PlatformIO…
Oliver
  • 39
  • 2
3
votes
0 answers

How do I install the USB drivers for Bigtreetech's SKR Mini E3 v1.2?

I want to install the USB drivers for the BIGTREETECH SKR Mini E3 v1.2 from the GitHub page but I don't know how to proceed. Any help will be greatly appreciated.
Liam
  • 679
  • 4
  • 12
  • 20
2
votes
1 answer

BLTouch clone will not deploy, stow, or deploy when homing or auto leveling

I have 2 printers, an Artillery Sidewinder X1 and an Ender 3 that both have BLTouch sensors installed. This post is about the one (BLTouch clone, the probe is a Smart v3.1 sensor) installed on my Ender. My problem: I recently upgraded from…
Artichoke
  • 187
  • 2
  • 14
2
votes
2 answers

Why would all of the Ender 5 Pro's axis motors (X, Y and Z) stop being able to move (all at once)?

I have a Creality Ender 5 Pro which has been working properly for some time. During my last print, the axis motors just suddenly stopped working while the extruder motor continued to work properly. In fact, when I connect the extruder motor wire to…
Mahlomola Daniel Cwele
  • 51
  • 5
2
votes
2 answers

While heating, BLTouch mesh data gets worse and worse the more times you probe

The title pretty much sums up the issue. It was happening before moving to an SKR Mini E3 V1.2 and is still happening with the new board. If I run A G28, then a G29 - while not heated - I will get some mesh data (poor mesh data because I haven't…
DreamingInsanity
  • 31
  • 5
2
votes
1 answer

BigTreeTech mini e3 V1.2 endstop installation

I recently purchased a BigTreeTech mini e3 V1.2 controller for my custom built 3D printer (as opposed to an pre-purchased ender 3). In doing so, I ran into the problem that the endstops I have been using have three wires: Power, Ground, and signal.…
Jack Hasselbring
  • 89
  • 1
  • 6
1
vote
0 answers

How to fix Y axis is off by 30 mm?

I have Ender 3 with Klipper. In my config: [stepper_y] step_pin: PB10 dir_pin: !PB2 enable_pin: !PB11 microsteps: 16 rotation_distance: 40 endstop_pin: ^PC1 position_min: -30 position_endstop: -30 position_max: 200 homing_speed: 50 With this, when…
Alex Buznik
  • 111
  • 2
1
vote
0 answers

Why are printed holes skewed diagonally?

My printer started off as an Anet A6. I've switched it to an aluminum extrusion frame, installed a BLTouch, switched everything to 24 V, gave it an ARM controller, etc. Printing runs over Octoprint. Material is ASA at 255 °C with the bed at…
Wojciech
  • 41
  • 1
1
vote
0 answers

SKR Mini E3 V2 - PWM on PC12 possible?

The SKR Mini E3 V2 uses the STM32F103RCF6 MCU based around ARM. I want to control the pin PC12 with PWM. However, this pin is not working as the Laser PWM signal. It never gets triggered actually with G0/G1 S0-255, although I am absolutely sure,…
HeartOfGermany
  • 11
  • 1
1
vote
0 answers

How can I successfully set up my fans to run on my CR-10 using Marlin?

I have a CR-10 (original version), and I just installed an SKR E3 Mini V3.0 board, with custom Marlin firmware. Everything else seems to be running properly, but some of my fans won't spin, or won't spin correctly. The CR-10 has four fans: the…
Jack Harris
  • 131
  • 4
1
vote
0 answers

Ender 3 V2 with new SKR mini e3 v3 is heating up extremely slowly

I just replaced my motherboard with a new SKR mini e3 v3 and changed the config files myself based on this Consolidated Marlin Guide. Unfortunately, It is taking over 10 minutes to heat up the bed which I've never experienced before. I've checked…
selacey
  • 11
  • 1
1
vote
1 answer

What causes checksum mismatch error while printing from OctoPrint?

Recently, I've installed a new BIGTREETECH SKR mini E3 V3.0 board on Creality Ender-5. Previously, I was using SKR mini E3 V1.2 board, but it broke down and I had to replace it. I connected new one exactly like the previous board and calibrated the…
kosteklvp
  • 1,181
  • 1
  • 6
  • 25
1
2