3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [mks]

18 questions
3
votes
1 answer

How to add custom physical buttons to a 3D printer in Marlin software

I have a 3D printer with MKS Robin mainboard + TMC2209. How do I add a piece of code to Marlin, for example, to make a physical button to start preheating, etc. I would like to use the existing mainboard, I don't want to use OctoPrint. I have basic…
Piotr
  • 31
  • 2
3
votes
1 answer

Stepper Motors getting extremely hot

I installed MKS Gen L V2.1 with TMC 2209 drivers to my Creality Ender-3 printer and updated the software to marlin 2, the stepper motors are getting extremely hot. What should i due to resolve this problem. The following Code is from the…
Rayan
  • 89
  • 1
  • 6
3
votes
0 answers

Retraction fine but recovery occasionally just doesn't happen

I'm having issues with retraction. My printer prints very well normally, but has an intermittent problem with retraction: the retraction itself always happens, but sometimes the subsequent recovery just doesn't take place, which obviously results in…
Bob Sammers
  • 139
  • 2
3
votes
2 answers

How can I print to my FLSUN QQ over Wi-Fi?

I want to be able to control my FLSUN QQ over Wi-Fi and don't have OctoPrint or a Raspberry Pi to run it on.
linuxdan
  • 1,403
  • 1
  • 13
  • 28
2
votes
0 answers

Configure MKS Robin WiFi Module on FLSUN Super Racer without Klipper

I recently purchased an MKS Robin wifi module for my spouse's FLSUN Super Racer after noticing that the printer runs on an MKS Robin Nano V3.1 board. Immediately after installing the chip, I saw it broadcasting a network, so I connected to it and…
Joshua Dannemann
  • 103
  • 8
2
votes
1 answer

Stepper motor driver dead?

I own a cheap 3D printer FLSUN Delta, which was bought 6 years ago. Several structural and other upgrades were done, such as additional frame links, a new heated bed with external MOSFET. In the past week in the middle of a print, the printhead came…
tomaz
  • 21
  • 2
2
votes
1 answer

Marlin 1.0 works: Marlin 2.0 destroys Z-axis motion

I have an FLSun 3D Cube, running off an MKS GEN V.1.4 main board. With Marlin 1.0, the Z-axis works great (and has been for three years). When I try to upgrade to Marlin 2.0, moving the Z-axis 10 mm results in extreme motion -50 mm at least, left…
Bill in Kansas City
  • 223
  • 1
  • 9
2
votes
1 answer

Thermal runaway

I have a bit of a headache with my Anycubic i3 Mega which originally had a Trigorila 32-bit board. I decided to swap it because of loud A4988 drivers and got myself an MKS Robin Nano 1.2. This printer is heavily modded. All the hot-end is swapped to…
Martynas
  • 115
  • 4
1
vote
2 answers

Error "TMC2208 or TMC2209 on Z2 requires Z2_HARDWARE_SERIAL or Z2_SERIAL_(RX|TX)_PIN

I am getting this error when I try to enable the Z2 driver for MKS Gen L V2.1 Could anyone help? Error "TMC2208 or TMC2209 on Z2 requires Z2_HARDWARE_SERIAL or Z2_SERIAL_(RX|TX)_PIN.
Rayan
  • 89
  • 1
  • 6
1
vote
0 answers

How to enable Z-offset on MKS TFT28 V4.0

I am trying to enable Z-offset on MKS MKS TFT28 V4.0 touch screen but I couldn't for some reason. This is the code that I have uploaded to the Screen firmware in which you can see that I have enabled the babystepping function: #the color of screen…
Rayan
  • 89
  • 1
  • 6
1
vote
0 answers

MKS / Bigtree Closed Loop stepper the same?

Is the MKS and BigTree closed loop stepper the same? I see more responses to BigTree question. I read BigTree was plug and play and seems to be getting good support from them. I'm using the MKS product and trying to go from a standard Nema17 to the…
Greg
  • 19
  • 3
1
vote
0 answers

Anycubic Kossel Delta switch from Trigorilla to MKS Gen L 1.0

I have an Anycubic Kossel Delta 3D Printer. The original Trigorilla motherboard died and I decided to buy one but I only found a Makerboard MKS Gen L 1.0 which is said to be compatible with Trigorilla. My questions are: I have 2 fan ports on…
Davinho
  • 33
  • 5
1
vote
1 answer

Connecting (Anet A8) 2004 display to MKS GEN L V2.0

Although it seems this question has been answered before Connecting (Anet A8) 2004 display to MKS GEN L this one differs because the v2.0 board has no obvious AUX-2 connector. So the question is, how can I connect the Anet A8 LCD Panel (with…
Aviator
  • 113
  • 3
0
votes
0 answers

Motors don't move when printing but do when homing

I have an MKS Robin Pro I was starting a print on and the motors were not moving. The progress bar was running and the extruder temperature was changing (IDEX printer) so I thought it was printing but the motors were not moving, so nothing actually…
Techn0L0gic
  • 11
  • 1
0
votes
0 answers

How I could make that my PC can recognize MKS SGen L V1.0

I have a Custom Printer BLV, but since I bought the board, MKS SGen L V1.0, never had been possible for any PC can recognize the board. Now, I'm having an issue with the temperature calibration, and it's impossible to set a setting for the PID. Is…
Pedro Miguel Pimienta Morales
  • 353
  • 1
  • 4
  • 12
1
2